Sửa chữa DAEWOO-LACETTI 2010 - P10

NUBIRA/LACETTI SEALING, CAULKING AND DEADNER 9–1
SECTION 9
SEALING, CAULKING AND DEADNER
CONTENTS
1. SEALING & CAULKING 9 – 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2. DEADNER 9 – 14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.1.GENERAL DESCRIPTION 9–14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.2.REPAIR PROCEDURE 9–14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9–2 SEALING, CAULKING AND DEADNER NUBIRA/LACETTI
1. SEALING & CAULKING
Note : Seal the following areas to prevent air leaks water leaks, and rust.
ENGINE ROOM .
Fig. 1 Engine Room
NUBIRA/LACETTI SEALING, CAULKING AND DEADNER 9–3
ENGINE ROOM
Fig. 2 Engine Room
9–4 SEALING, CAULKING AND DEADNER NUBIRA/LACETTI
DASH
Fig. 3 Dash
NUBIRA/LACETTI SEALING, CAULKING AND DEADNER 9–5
FLOOR & TRUNK ROOM
Fig. 4 Floor & Trunk Room
9–6 SEALING, CAULKING AND DEADNER NUBIRA/LACETTI
REAR LAMP & TRUNK ROOM
Fig. 5 Rear Lamp
NUBIRA/LACETTI SEALING, CAULKING AND DEADNER 9–7
Fig. 6 Rear Lamp
9–8 SEALING, CAULKING AND DEADNER NUBIRA/LACETTI
ROOF
Fig. 7 Roof
NUBIRA/LACETTI SEALING, CAULKING AND DEADNER 9–9
ROOF
Fig. 8 Roof
9–10 SEALING, CAULKING AND DEADNER NUBIRA/LACETTI
SUN ROOF
Fig. 9 Sun Roof
NUBIRA/LACETTI SEALING, CAULKING AND DEADNER 9–11
HOOD & TRUNK LID
Fig. 10 Hood & Trunk Lid
9–12 SEALING, CAULKING AND DEADNER NUBIRA/LACETTI
TAILGATE
Fig. 11 Tailgate
NUBIRA/LACETTI SEALING, CAULKING AND DEADNER 9–13
FRONT & REAR DOOR
Fig. 12 Front & Rear Door
9–14 SEALING, CAULKING AND DEADNER NUBIRA/LACETTI
2. DEADNER
2–1. GENERAL DESCRIPTION
.
Deadner is properly designed and applied for reduce the
vibration and noise. Also, it plays in maintaining the
structural rigidity of the panel.
.
2–2. REPAIR PROCEDURE
.
1. Remove the related parts.
S Seats, carpet.
S Trims, others.
.
2. Removal of the damaged deadner.
S Peel off the damaged deadner with a steel spatula, care-
fully.
.
3. Clean and dry.
S Before applying the deadner, thoroughly clean and dry
the areas to be applied.
.
4. Prelocation the new deadner on the panels to be ap-
plied.
.
Note : Avoid the parts mounting holes and service holes.
.
5. Adhension of deadner.
S Heat the surface of deadner with a torch or heating gun
until it adheres itself.
S Push and adhere to the panel with a rubber spatula.
.
Note : In order to take full advantage of the deadner, its
face must adhere and contact the panels perfectly.
.
CAUTION : Be careful not to burn the composite
parts when beating.
Fig. 13
6. Install the related parts.
S Install in the reverse order in which they were removed.
Fig. 14

Xem chi tiết: Sửa chữa DAEWOO-LACETTI 2010 - P10