Tài liệu Fast Way to get your Certification - Exam :640-604 ppt

- 5 -


Answer: C.
Explanation: In the client VTP mode VTP client behave the same way as VTP servers, but cannot create,
change, or delete VLANs on a VTP client.




QUESTION NO 6
You have several VLAN trunks in your Auto and off modes. You are entering a new port. Which mode
must you want the port to be in permanent trunking mode? (Choose two)

A. On
B. Off
C. Auto
D. Desirable
E. No negotiate


Answer: A and E.
Explanation: Both on and the no negotiate modes will put a port into permanent trunking mode. With no
negotiate mode the neighboring port must be manually configured.



QUESTION NO 7
Given the VTP mode table, place the VTP mode in the correct location at the top of the table.

www.correctexams.com

Fast Way to get your Certification


- 6 -

Answer:


Explanation: VTP server mode is the most comprehensive VTP mode. Client mode is a close second with the
only difference is that VTP clients cannot create, change, or delete VLANs on a VTP client, and Transparent
mode does not participate in VTP.



QUESTION NO 8
You are configuring a VLAN on fast Ethernet. Which two trunking modes make the port able to convert
the link to trunk link? (Choose two)

A. Off
B. Auto
C. Desirable
D. Negotiate
E. Nonegotiate


Answer: B and C.
Explanation: Both Desirable and Auto modes to convert links to trunk link. Desirable mode does this
conversion actively and auto the port is willing to convert.



QUESTION NO 9
An Ethernet media trunk link is configured and is operating between two Cisco switches. Each switch has
identical module, software revisions and VLAN configuration information. Spanning-Tree Protocol is
disabled on all VLANs. Problems have been identified regarding frames leaking between two VLANs.
What is the most likely cause of this problem?

A. The duplex mode is different at each switch.
B. The link is using IEEE 802.1Q protocol in point to point mode.
www.correctexams.com

Fast Way to get your Certification


- 7 -

C. The link is using 802.10 trunk protocol, with the SAID parameters incorrectly set.
D. The link is using ISL protocol and the native VLAN information is different at each end of the link.
E. The link is using IEEE 802.1Q protocol and the native VLAN information is different at the each
end of the link.


Answer: E
Explanation: The most likely reasons for frames leaking between two VLANs is that the link is using IEEE
802.1Q protocol and the native VLAN information is different at the each end of the link.



QUESTION NO 10
You need to enter a switch into and existing VTP domain without altering the configurations of the
systems currently on the domain. Which two conditions ensure that the new switch will not change the
existing VTP Domain configuration? (Choose two)

A. The switch must be in client mode.
B. The trunk links must not be configured for ISL
C. The VTP domain must not have a password assigned to it.
D. The clear config all command must be executed on the switch and be rebooted.


Answer: A and D.
Explanation: Whenever you enter a switch into an existing VTP and do not it to effect the configuration of
systems on the domain, this switch should have the clear config all command executed and then rebooted.
Finally the switch should be put into the client mode.



QUESTION NO 11
An Ethernet media trunk link is to be configured between two Cisco switches each having identical
module, software revisions and VLAN configuration information. Which two are required for the trunk
to operate? (Choose two)

A. The link is 100MB/s or slower.
B. The link uses IEEE 802.1Q trunk protocol.
C. The link must be point to point if it is ISL.
D. The link must have different trunk encapsulation at each end.
E. The link may use IEEE802.1Q trunk protocol, providing the SAID parameter is correct set.


Answer: B and C.
www.correctexams.com

Fast Way to get your Certification


- 8 -

Explanation:
B: The IEEE 802.1Q trunk protocol can be used.
C: ISL operates in a point-to-point environment

For a trunk to operate it require a protocol, such as IEEE 802.1Q, and SAID parameters must be set properly.

Incorrect Answers
A: There is no speed 100Mb/s speed limit.
D: This is incorrect.
E: Cisco implements VLANs over FDDI medium using 802.10 encapsulation. This encapsulation adds a tag
(SAID) to the frames. SAID is not used by the IEEE 802.1Q protocol.



QUESTION NO 12
Which statement best describes a trunk link?

A. The trunk link belongs to a specific VLAN.
B. A trunk link only supports a native VLAN for a given port.
C. Trunk links use 802.10 to identify VLAN over an Ethernet backbone.
D. Trunk links are used to connect multiple devices on a single subnet to a switch port.
E. The native VLAN of the trunk link is the VLAN that the trunk uses if that link fails for any reason.


Answer: E.
Explanation: A trunk link can have a native VLAN. The trunk’s native VLAN is the VLAN that the trunk uses
if the trunk link fails for any reason.



QUESTION NO 13
You are troubleshooting problems on the Catalyst 5000 trunk and you notice that there is a disagreement
about the VLAN configured to use the trunk. What can you do?

A. Remove all the VLANs set for the trunk.
B. Reload the active VLAN configuration settings.
C. First clear the affected port and then bring it back up.
D. Explicitly set or clear the trunk for the VLAN to be on.
E. Set or clear VLANs on both sides of the link so values do not match.


Answer: D.
www.correctexams.com

Fast Way to get your Certification


- 9 -

Explanation: To ensure that there is agreement in the VLAN configuration you should explicitly set or clear
the trunk for the VLAN to be on.



QUESTION NO 14
When checking that the switch and router are consistently configured for VLANs, Cisco engineers
typically recommend that VLAN ID 1 ______

A. Has a maximum transmission unit of 4352.
B. Be configured for concurrent routing and bridging.
C. Be used for management and troubleshooting only.
D. Uses and ID that is identical to the default SAID value.
E. Spans a network diameter of no more than eight devices.


Answer: C
Explanation: It is recommended that VLAN 1 be reserved for administrative purposes: management and
troubleshooting.



QUESTION NO 15
By default, the Catalyst switch software sends error messages to the console terminal. Enter the
command you would use to check for error messages if they are redirected to another destination.


Answer: show logging
Explanation: The show logging command can be used to display the system message log configuration.



QUESTION NO 16
What does it mean when LEDs flash during the Catalyst 5000 power up-sequence?

A. One or more modules is not correctly inserted in to its slot.
B. The power-up sequence is underway and not yet completed.
C. One or more fan, power supply, or supervisor clock is disabled.
D. The network management autodiscovery process is under way.
E. The traffic testing process of an interface loopback has not yet completed.


Answer: B.
www.correctexams.com

Fast Way to get your Certification


- 10 -

Explanation: When LEDs flash during power up it indicates that power up is underway and not yet completed.



QUESTION NO 17
For an indicator of an active link state on a Catalyst port, you should look at the _______

A. Port’s link Led on the Switching Module.
B. Port Link OK LED on the Link Integrity Module.
C. Status LED on the network Management Module.
D. Solid green LED on the port’s Route Switch Module.
E. Switch link load LED on the Supervisor Engine Module.


Answer: A.
Explanation: The quickest way to confirm if a Catalyst port is active or not is to look at the Port’s link LED.



QUESTION NO 18
What command must you use to enable CGMP on router interface?

A. Ip cgmp
B. Pip cgmp
C. Ip pip cgmp
D. Interface cgmp


Answer: A.
Explanation: To enable CGMP, enter the ip cgmp command in the interface command mode.



QUESTION NO 19
In order for the CGMP to operate correctly on a switch, the switch must have a network connection to a
__________

A. Switch running IGMP
B. Router running CGMP
C. Switch running CGMP
D. Switch that has VLAN configured


www.correctexams.com

Fast Way to get your Certification


- 11 -

Answer: B.
Explanation: In order for CGMP to operate correctly on a switch, the switch must have a network connection
to a router running CGMP. A CGMP-capable IP multicast router detects all ICMP packets and informs the
switch when specific hosts join or leave IP multicast groups.



QUESTION NO 20
Which command is used to disable CGMP on a set command based switch?

A. Disable cgmp
B. Set cgmp off
C. Shutdown cgmp
D. Set cgmp disable


Answer: D.
Explanation: To disable CGMP on a switch, enter the set cgmp disable command.



QUESTION NO 21
You are preparing to install a UTP cable connection. You should have no more than _____

A. Five meters from the switch to the patch panel.
B. Ninety meters from the punch down block to the switch.
C. Ten meters from the punch down block to the desktop connection.
D. Fifty-five meters from the patch panel to the office punch down block.


Answer: A.
Explanation: Most cable installers recommend that the 100-meter rule be followed when installing UTP cable
connections. The 100-meter rule is broken further down. One of these distances is five meters from the switch
to the patch panel.



QUESTION NO 22
To configure the fast Ethernet connection between your access switch and primary distribution switch,
which two steps are highly recommended? (Choose two)

A. Set the port speed on your access switch.
B. Assign an IP address to your access switch.
www.correctexams.com

Fast Way to get your Certification


- 12 -

C. Set the port speed on your primary distribution switch.
D. Set the port duplex on the primary FE mod/port on your access switch.


Answer: A and D.
Explanation: In order to configure a fast Ethernet connection between your access switch and the primary
distribution switch that you must first set the port speed on the access switch and then you must set the port
duplex on the primary FE mod/port on your access switch.



QUESTION NO 23
When setting the duplex on a Catalyst 1900 series switch backup link, the auto argument _______
(Choose two)?

A. Is only valid on 10baseT port.
B. Is the default for the 100baseTX port.
C. Negotiates full duplex connectivity with the connecting device.
D. Places a 100baseTX port into full duplex mode with flow control.


Answer: B and C.
Explanation: When the line mode of the Catalyst 100 is set auto it negotiates full duplex connectivity with the
connecting device. Please note default line mode for the 100BaseTX is auto.



QUESTION NO 24
You have connected a cable between a Catalyst 1900 and 5000 series switch. When correctly connected,
the port status LED light located on _______.

A. Both switches should NOT light up.
B. Both switches should light up and remain on.
C. Both switches should stay lit for 60 seconds, and then turn off.
D. The catalyst 1900 lights up for 30 seconds, then turns off, and the catalyst 5000 port status LED
stays lit.
E. The catalyst 5000 lights up for 30 seconds, then turns off, and the catalyst 1900 port status LED
stays lit.


Answer: B.
www.correctexams.com

Fast Way to get your Certification


- 13 -

Explanation: The port status LEDs area good way to troubleshoot a switch. When a switch boots up the LEDs
will flash green. After this if everything is working correctly the LEDS should remain a solid green on both
switches.



QUESTION NO 25
Your IS manager has assigned you to configure a backup link on an IOS-based command switch. Which
command must you use to configure the interface/port for full duplex?

A. Duplex
B. Duplex full
C. Full duplex
D. Duplex auto
E. Port duplex full


Answer: B.
Explanation: The command that should be used is set port duplex full. This will achieve the desired effect.



QUESTION NO 26
Which two does Ethernet LAN switching use? (Choose two)

A. MPOA
B. IEEE 802.10
C. IEEE 802.1D
D. Multicast OSPF
E. Spanning-Tree Protocol


Answer: C and E.
Explanation: IEEE 802.1D is the standard for STP. STP is used to prevent loops.



QUESTION NO 27
You have a link between the distribution and core switches that is configured for autonegotiation. To
ensure the most efficient connection, which duplex mode would you select?

A. Half
B. Full
www.correctexams.com

Fast Way to get your Certification


- 14 -

C. Auto
D. Full-flow-control


Answer: B.
Explanation: When auto negotiation is configured it is best to set the duplex to Full. This will lead to less
amount of effort for the switch and more efficient use of resource.



QUESTION NO 28
You have a set-based switch. Which command do you enter to assign an IP address an interface?

A. IP address
B. Set IP address
C. Set interface sc0
D. Interface ethernet


Answer: C.
Explanation: If a switch is set-based, you assign the IP address to the in-band logical mode. In privilege mode
you will need to enter the set interface sc0 command.



QUESTION NO 29
You want to use hardware-based bridging to switch between Ethernet and Fast Ethernet, and you need
to increase the network bandwidth. However, you do not want to make an expensive network overly
complicated.
Which ISO layer is associated with these functions?

A. Sessions
B. Network
C. Data link
D. Physical
E. Transport
F. Application
G. Presentation


Answer: C.
Explanation: Hardware based bridging is Layer 2 switching. Layer 2 of the OSI model is the Data Link.

www.correctexams.com

Fast Way to get your Certification

Xem chi tiết: Tài liệu Fast Way to get your Certification - Exam :640-604 ppt